Air inlet pipe and pump body
(1) The pump is not filled with enough water prior to start-up, and sometimes it appears that the water has been spilled from the bleed hole, but the air is not completely discharged by the pump shaft, causing a small amount of air to remain in the inlet pipe or pump body.
(2) The horizontal section of the inlet pipe in contact with the pump applies a descending gradient of 0.5% or more to the direction of the flow of water, and the one end connected to the inlet of the pump is the highest, not completely horizontal. If you tilt up, there will be trapped air inlet pipe, reducing the vacuum hose and pump, affecting water absorption.
(3) The packing of the pump is worn or the packing pressure is too loose due to the long-term use, resulting in a large amount of water being ejected from the gap between the packing and the shaft sleeve of the pump. As a result, external air flows into the pump from these gaps, Affected the mention of water.
(4) Inlet pipe Due to long-term potential underwater, pipe wall corrosion holes, water pumps continue to decline after work, when these holes exposed water, the air from the hole into the civilian into the water pipe.
(5) cracks in the inlet pipe cracks, inlet pipe and pump connections appear tiny gaps, are likely to make the air into the inlet pipe.
Pump speed is too low
(1) human factors. Some users due to the original motor damage, it is coupled with another motor driven, the result of a small flow, low lift or even the consequences of the water.
(2) the pump itself mechanical failure. Loosening of the impeller and the shaft of the pump shaft or the deformation and bending of the shaft of the pump cause the impeller to move more, friction directly with the pump body or damage to the bearing, all of which may reduce the speed of the pump.
(3) power machine repair is not working. Motor due to the winding burned, and lost magnetism, the maintenance of the winding turns, diameter, wiring changes, or maintenance failure is not completely ruled out the factors that will change the pump speed.
Suction too much
Some of the water is deep and some of the water's outer surface is flat, ignoring the allowable suction of the pump, resulting in little or no water absorption. To know the pump suction port can establish a degree of vacuum is limited, the absolute vacuum suction is about 10 meters high water column, and the pump can not establish an absolute vacuum. And the vacuum is too large, easy to pump the water gasification, the work of the pump negative. Therefore, the centrifugal pump has its maximum allowable suction, usually between 3-8.5 meters. Do not install the pump only easy and simple.
Water flow in the water pipe resistance loss is too large
Some users through the measurement, although the vertical distance from the reservoir or water tower to the water surface is slightly less than the head of the pump, but still small amount of water or mention the water. The reason is often too long pipes, pipe corners, water flow resistance in the pipeline is too large loss. The reason is often too long pipes, pipe corners, water flow resistance in the pipeline is too large loss. Under normal circumstances, 90-degree bend than the 120-degree elbow resistance, each 90-degree elbow head loss of about 0.5-1 meters, 20 meters of pipe resistance can make head loss of about 1 meter. In addition, some users are also free to pump into and out of the pipe diameter, which also has a certain impact on the lift.
Other factors
(1) The bottom valve can not open. It is usually due to the pump being left on for too long, the bottom valve gasket is stuck, and the bottom valve without gasket may rust out.
(2) The bottom valve filter screen is clogged; or the bottom valve causes potential clogging of the filter screen in the sludge layer.
(3) impeller wear serious. Impeller blades worn by long-term use, affecting the pump performance.
(4) Gate valve can check valve failure or blockage will result in reduced flow or even pumping on the water.
(5) Leakage of the outlet pipe will also affect the amount of water lift.
More Search Keywords: water pump
China Electric Processor,Mini Mixer For Home-Used, 4 in 1 Electric Blender Mixer,Mini Blender Mixer, we offered that you can trust. Welcome to do business with us.
Jiangmen Hongyi Electrical Appliance Manufacturing Co., Ltd. is a professional enterprise which aims at producing household electrical appliances. Our company is located in Jiangmen City, Guangdong Province. We are adjacent to Guangzhou, Shenzhen, Macao and Hong Kong. The transportation is very convenient.
Our company has product development, mould manufacturing, testing, product manufacturing and other departments. We have a professional team to ensure product quality. We provide quality and high performance products for clients. Our company aims to establish good and stable trade relationships with clients. Our products are exported to Southeast Asia, the Middle East and other countries and regions. We have deeply won consumer's trust.
Our main products are food mixers, blenders, electric fans, electric irons, plastic accessories and hardware.
Our company has consistently adhered to the concept of "outstanding quality, affordable price, excellent service". We hope to strengthen economic cooperation with friends from all over the world and create a bright future together.
Electric Processor,Mini Mixer For Home-Used,4 in1 Electric Blender Mixer,Mini Blender Mixer
Jiangmen HongYi Electrical Appliance Manufacturing CO.LTD , https://www.hongyiappliances.com