Automatic HDPE Plastic Bottle Blow Molding Extrusion Blowing Moulding Making Machine

Automatic Plastic bottle Blow Molding Machine extrusion blow moulding machine

Asone of the biggest factory for blow molding machine in China, we have already exported to over 60 countries in the world, like  America, England, Sri Lanka, Italy Switzerland, Newzealand, Egypt.etc. In 2009, we manufactured successfully a 3000 liter blow molding machine which is the biggest one in China.

Maximum Volume: 5 litter
Material: HDPE, PP, PVC, PETG etc.
View Stripe matchable
Easy operation
Automatically
1>Double station and single satation
2>Single mould head to six mould head
3>Mutli-layer with View Strip line
4> It can match auto-deflashing device, Leak detector, Chiller and crusher recycle system.
5> The daliy output(24 hours) can reach approximately from 5, 000 to 86, 000; It can produce from 0.2-5L plastic hollow bottle products.

A.Brief Introduction
DMK-L series are fully-automatic pet stretch-blow molding machines(preheat). It has 3 to 16 cavities and the maximum capacity of the products is 2000mL. It can blow bottles in shapes: carbonated, mineral, pesticide, cosmetics, wide-mouth, hot filling, and other packing containers, which is made of plastic of crystalline type, such as PET and PP etc. 
1).High Automatization
2).High Intelligence:The machine can be controlled through touch screen and running status is shown on it.
3).High Quanlity:Steady infrared heating system blowing and highly precise blow-mould closing system ensure quality.
4).High Speed:6000BPH(6-cavity), 8000BPH(8-cavity), 12000BPH(12-cavity), 16000BPH(16-cavity).
5).No Contamination:Closed production zone, good self-lubrication system avoid contamination.
6).Low Cost:Low consumption of electricity, air and water.
7).High Transparency:Easy maintenance, absolute safely, visual inspection, low noise.
 
B.Settings:
a).PLC colour display: SIEMENS(GERMANY)
b).Pneumatic parts:FESTO(GERMANY)
c).Controller of preform transfer:Servo motor National(JAPAN)
d).Other electric parts are all world-famous brand 

C.Machine Features:
C.1. Stable performance with advanced PLC.
C.2. Conveying preforms automatically with conveyor.
C.3. Strong penetrability and good and swift distribution of the heat by letting the bottles rotate by itself and revolute in the rails simultaneously in the infrared preheater.
C.4. High adjustability to enable the preheater to preheat preforms in shapes by adjusting the light tube and the length of the reflecting board in the preheating area, and eternal temperature in the preheater with an automatic thermostatic apparatus.
C.5. High safeties with security automatic-locking apparatus in each mechanical action, which will make the procedures turn into a state of safety in case of a breakdown in certain procedure.
C.6. No contamination and low noise with the air cylinder to drive the action instead of the oil pump.
C.7. Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine.
C.8. Strong clamping force with high pressure and double crank links to lock the mold.
C.9. Two ways of operating: automatic and manual.
C.10. Safe, reliable, and unique design of the position of valve to make the air pressure diagram of the machine easier to understand.
C.11. Low cost, high efficiency, easy operation, easy maintenance, etc, with automatic technological process.
C.12. Contamination is avoided for the bottle body.
C.13. Ideal effect of the chilling with the chilling system.
C.14. Easy installation and starting
C.15. Low rejection rate: less than 0.2 percent. 
Blow Molding Machine Picture:



Processing Machine:



 
Any question, contact with me
MOB:+8613915728281 
   
 

Centrifugal Spray Granulation Dryer

Lab Spray Dryer,Small Spray Dryer,Centrifugal Drying Machine,Centrifugal Spray Granulation Dryer

Wuxi Tianyang Drying equipment Co.,Ltd , https://www.srowavmachinery.com