Automatic Stud and Track Roll Forming Machine

1, Main Parameter
1), Raw Material : hot-dip galvanized steel strip
2), The thickness of the raw material: 0.5-1.8mm
3), The width of the feed-in:300mm
4), Main drive motor: Servo controler and motor( IMS-GCT407.5WGL0D controler with Isolation card controlled servo motor SM-07.5C4S5)
5), Working voltage: 380v 50hz  
6), Forming steps: 14steps; Forming rollers with 3 points Support; Equipment running smoothly 
7), Gear reducer:ARC hard tooth surface gear reducer;Running noiseless. The reducer has a good return and durability. Servo motor special reducer.
8), Main forming machine use welded steel structure 
9), Transmission mode : gear wheel transmission( the material of the gear wheel use 45# steel, the surface disposed by high frequency )
10), Roller shaft use 45# steel, modulation disposal, the hardness of the modulation is  HB250-280.surface grinding. The outer diameter is 55mm 
11), Roller mould use Gcr15,salt bath quenching. hardness is HRC58-62
12), Production speed: 0-40M/min; Vertical keel for partition wall punching speed: 18M/min
13), Max tolerence of the forming products : 0.4mm
14), Feed-in material way : from left to right
2,Vertical uncoiler deviceL Model No.:MT-400
    1) Max uncoiler width  350mm
    2) Thickness of the material  2.0mm
    3) Inner diameter of the coil  450-530mm
    4) Outer diameter of the coil  1500mm
    5) Max bear weight of machine  1200kg
    6) Tension is hand brace
    7)Motor driven device
 3,Cutting/punching device 
    1) Cutting device not stop, servo cut off; Servo motor driven( IMS-GCT407.5WGL0D controler with 
 
Isolation card controlled servo motor SM-07.5C4S5); High precision Ball screw drive
2) Cutting power   High speed hydraulic cutting.( 0.6s can complete one set cut reciprocating.)
   3) The form of the cutting: 45 degree skew; No cutting scrap
    4) High speed hydraulic cutting and punching
4,Operation Panel and control
    1) Touch screen panel;Cutting length and products quantity can be set freely;The machine can automatic stop once the set up production quantiy finished.
    2) Main machine control: PLC control 
    3) Length measure: High precision Rotary encoder .Fixed - length precision ±1.5mm
5. Packing List for Machine

Oxide Ceramics Powder

Oxide powder for thermal spray refers to a type of powder material that is used in thermal spray processes. Thermal spray is a coating technique where a material in powder form is heated and propelled onto a substrate, forming a coating.

Oxide powders are commonly used in thermal spray applications due to their high melting points, excellent wear resistance, and thermal insulation properties. They can be used to create protective coatings on various surfaces, such as metals, ceramics, and plastics.

Some common types of oxide powders used in thermal spray include:

1. Aluminum oxide (Al2O3): This oxide powder is widely used for its high hardness, wear resistance, and thermal insulation properties. It is commonly used for coating applications in industries such as aerospace, automotive, and electronics.

2. Zirconium oxide (ZrO2): Zirconium oxide powder is known for its high melting point and excellent thermal barrier properties. It is often used in thermal spray coatings for gas turbine engine components, where thermal insulation is critical.

3. Chromium oxide (Cr2O3): Chromium oxide powder is used for its high hardness, corrosion resistance, and wear resistance. It is commonly used in applications where high temperature and abrasive wear resistance are required.

4. Titanium oxide (TiO2): Titanium oxide powder is known for its high refractive index and excellent UV resistance. It is often used in thermal spray coatings for optical and decorative applications.

These oxide powders can be applied using various thermal spray techniques, such as flame spraying, plasma spraying, or high-velocity oxy-fuel (HVOF) spraying. The choice of oxide powder and thermal spray technique depends on the specific application requirements and desired coating properties.

Oxide Ceramics Powder,Pure Aluminum Oxide Powder,Chromium Oxide Ceramics Powder,Yttria Stabilized Zirconia Powder

Luoyang Golden Egret Geotools Co., Ltd , https://www.lygoldentool.com