Our factory is specialized in different kinds of roll forming machine ,also we can design the machine according to you products details :
Roofing and wall panel roll forming machine ,Glazed tile roll forming machine ,Roof ridge cap roll forming machineÂ
Shutter door roll forming machine ,Pu foam shutter door production line,Door frame roll forming machineÂ
Ceiling keel roll forming machine,Tee grid roll forming machine ,C&Z purlin roll forming machine
Floor decking roll forming machine,Pipe roll forming machine and bending machineÂ
Gutter roll forming machine,Guardrail roll forming machine,Stone coated steel tile production lineÂ
Sandwich panel production line ,Slitting line,Curving machine,Decoiler,Cutting and bending machine
__________________________________________________________________________________________________________
                     Â
              High Speed Metal Stud and Track Roll Forming Machine
A. Uncoiler.......................................................................1 unit
B.Main roll forming machine  ·································· 1 unit
C. Control panel·····················································1 unit
D. Accepting table..............................................................1 unit
E.Hydraulic pump...............................................................1 unit
Details of each roll forming machine composition:
(1) 4 feet manual uncoiler
(2)Capacity of the uncoiler  : 5 tons
(3) Range of segment expansion  : 460 ~ 515 mm
(4) Inner diameter of coil  : 508mm
(5)Maximum width of coil  : 1300mm
variety of styles to meet different requirements
Â
Main roll forming machine
1. Forming stations  : 13 stations
2. Material of roller  : Cr12 heat treatment HRC60 and surface is being hard chrome;
3. Shaft : Dia 80mm, high frequency surface treatment and grinding process;the material is 45#steel.
4. Horsepower  : 5.5KW (The motor is used to drive the hydraulic pump ,which enables the hydraulic   oil to drive the hydraulic motor and then drives the main machine.)
5. Transmission  : Chains and gears
6. Forming speed  : 50 M/MINUTE
7. Forming thickness : 0.2 -0.7mm
  (1) High tensile coil is used, Yield Strength: 550MPa or less
  (2) The finished products will change if using different material and thickness.
8. Cutting:
  (1) Flat-sheet cutting: It is used when changing the coil of raw material; it
     can cut the coil rapidly and time- saving.
  (2) Cutting after forming: Cut the sheet after roll forming to required length
  (3) Cutting motion: No-stop cutting with the seivo motor
  (4) Material of blade: Cr12; heat treatment HRC59~61
  (5) Length measuring: Automatic length measuring
  (6) Tolerance of length: +/- 1.5mm
9. Approximate Size: Length: 4Â M * Width : 1.0Â M * Height : 1.3M
10.Characteristics of the main machine
   (1) Base is made of high tensile strength H beam with precision welded and
     good rigidity.
   (2)Shaft, roller and all components are manufactured precisely to have long
     lifetime.
   (3)Efficient design, easy maintenance
Control panel
(1) Voltage, Frequency, Phase:Â Customizable
(2) Automatic length measurement: one unit tooling of length measuring
   which is lightly pressed on the surface of the steel sheet; the tolling will roll
   with the moving speed of the steel sheet and then sense to measure its length.
(3) Automatic quantity measurement
(4) PLC is used to control length & quantity. Machine will automatically
   cut to length and stop when required quantity is achieved
(5) 99 kinds of dimensions can be set in one order at the same time,
   continuously production and nine orders can be keyed-in at a time.
(6) The total length of the order is automatically counted; when the
   material's supply is enough, the material will automatically stop entering the machine which is the    convenient device for orders (with different material) to change the material.
(7) Length inaccuracy can be amended easily.
(8) Control panel: Button-type switch, LED display length and quantity
(9)Unit of length: millimeter and inch (switched on the control panel)
(10) Motor Over-Load protection
(11) System Over-Current protection
(12) Short circuit protection
(13) Display total length produced
(14) Display total quantity produced
Hydraulic pump
Hydraulic system for cuttingÂ
The motor is used to drive the hydraulic pump ,which enables the hydraulic   oil to drive the hydraulic motor and then drives the main machine.
Accepting table (one manual for free)
lenght :4mÂ
__________________________________________________________________________________________________________
Pre-Sales Service
* Inquiry and consulting support
* Sample testing support.
* View our Factory.
Â
After-Sales Service
* Training how to instal the machine, training how to use the machine.Â
* Engineers available to service machinery overseas.
Â
Packaging | |
Packing method: nude, with waterproof cloth and stow-wood. The computer controlled cabinet is packed with waterproof cloth and box. The seller should guarantee equipment will be moisture-proof, anti corrosive, and will not be damaged during transportation.  | |
__________________________________________________________________________________________
1. Does one machine can only produce one style panel profile?
Not exactly.For wider and double layer making machine. It can produce more than 6 kinds of panels.
2. Do you have after sales support?
Yes, we are happy to give advice and we also have skilled technicians available across the world.We need your machines running in order to keep your business running.
3. How to visit your company?
a.Fly to Beijing airport: By high speed train From Beijing Nan to Cangzhou Xi(1 hour), then we can pick up you.
b.Fly to Shanghai Airport: By high speed train From Shanghai Hongqiao to Cangzhou Xi(4.5 hours), then we can pick up you.
4. How to get a quotation?
a. Give me the profile drawing and thickness, this is the important. If no,I will suggest you some.
b. Other specific requirements are welcome, such as the speed, power and voltage you want.
5. What can you do if the machine broken?
Our machine's warranty period is 12months! If the broken parts can't repair, we can send the new parts replace the broken parts free. If after warranty period,we can through negotiation for to solve the problems, and we supply the technical support for the whole life of the equipment.
6. Can you be responsible for transport?
Yes, please tell me the destination port or address. We have rich experience in transport.
7. You are trade company or factory?
We are factory. Welcome to our workshop for visiting.
8. How long the machine could be made?
Normally speaking, common roof profile roll forming machine could be made within 45 working days.
If you need machines in a hurry, we can make it for you less than a month.
If need more machine pictures or videos,welcome to contact me.
Â
Desulfurization pump Introduction
TL(R) model desulfurization pump is the new generation high efficiency energy saving product
elaborately researched and developed by our company through absorbing the technical advantages from
same products at home and abroad, with reference to the technical specifications of flue gas desulfurization
project, aiming at the characteristic of FGD system of transporting medium through pump in thermal power
plant.
Construction of Desulphurization Pump
Detail parameter of Desulphurization
Slurry Pump, Horizontal Slurry Pump, Centrifugal Slurry Pump, Desulphurization Pump, Centrifugal Pump, Mining Slurry Pump, Vertical Slurry Pump, Metal Slurry Pump
Shijiazhuang Naipu Pump Co., Ltd. , https://www.naipu-pump.com