Wireless bridges, wireless video transmission equipment from the previous work to see wireless bridge is a wireless network bridge, it uses wireless transmission to achieve a bridge between two or more networks to establish communication; wireless bridge from the communication mechanism It is divided into circuit bridges and data bridges. Then how do we debug after we purchase Shenzhen Leian Technology Wireless Bridge Video Transmission Equipment, how to connect wireless bridge equipment? The following Xiaobian gives you a brief introduction:
1. First, we must connect the wireless bridge to the camera through the POE. The network data input terminal is connected to the network camera. The bridge power supply port is directly connected to the wireless bridge. The DC12~24V is connected to the 220V AC through the power adapter. Power the bridge.
2. After the wireless bridge is connected, if the computer's local connection is frequently disconnected (a red cross appears) (this condition sometimes results in no signal), then the quality of the network cable you are using must be poor, resulting in insufficient power supply. The local connection is a direct cross, no response!
There are three solutions: replace the network cable with good quality; shorten the cable from the POE port to the bridge; increase the voltage and replace the 24V power supply with a 15V power supply (the motherboard supports up to 24V);
3, the rate is low, in order to avoid this kind of situation, please after installation, first set the transmitter to receive mode, use the transmitter to scan around the signal, after scanning to find out the strongest signal, check his frequency (channel) as far as possible To avoid this, for example, the strongest signal strength scanned at -60 is 2412 (Channel 1). Then you do not use this frequency, you can choose to avoid 2312 or 2457. (Above-75 interference usually does not constitute a threat).
4, 3 km distance, even if it is disconnected or intermittent, the reason may be that the antenna angle is not correct, resulting in weak signal, may exceed -75, in this case the user needs to open the receiving end of the WEB interface, watching the color bar behind The signal strength is used to adjust the angle of the antenna. For each adjustment, see if the value behind the “-†sign has decreased. If the signal is not ideal after adjusting the receiving angle, then the angle of the transmitting end should be adjusted to adjust the angle of the transmitting end. , is still to see the receiver page (preferably two people to adjust)
If you can't solve the problem according to the above methods, please call Shenzhen Lai'an Science and Technology personnel to consult!
1. First, we must connect the wireless bridge to the camera through the POE. The network data input terminal is connected to the network camera. The bridge power supply port is directly connected to the wireless bridge. The DC12~24V is connected to the 220V AC through the power adapter. Power the bridge.
2. After the wireless bridge is connected, if the computer's local connection is frequently disconnected (a red cross appears) (this condition sometimes results in no signal), then the quality of the network cable you are using must be poor, resulting in insufficient power supply. The local connection is a direct cross, no response!
There are three solutions: replace the network cable with good quality; shorten the cable from the POE port to the bridge; increase the voltage and replace the 24V power supply with a 15V power supply (the motherboard supports up to 24V);
3, the rate is low, in order to avoid this kind of situation, please after installation, first set the transmitter to receive mode, use the transmitter to scan around the signal, after scanning to find out the strongest signal, check his frequency (channel) as far as possible To avoid this, for example, the strongest signal strength scanned at -60 is 2412 (Channel 1). Then you do not use this frequency, you can choose to avoid 2312 or 2457. (Above-75 interference usually does not constitute a threat).
4, 3 km distance, even if it is disconnected or intermittent, the reason may be that the antenna angle is not correct, resulting in weak signal, may exceed -75, in this case the user needs to open the receiving end of the WEB interface, watching the color bar behind The signal strength is used to adjust the angle of the antenna. For each adjustment, see if the value behind the “-†sign has decreased. If the signal is not ideal after adjusting the receiving angle, then the angle of the transmitting end should be adjusted to adjust the angle of the transmitting end. , is still to see the receiver page (preferably two people to adjust)
If you can't solve the problem according to the above methods, please call Shenzhen Lai'an Science and Technology personnel to consult!
Workbench System,High-quality Adjustable Desk,Table Platform Four Kind Material,Group Using Together
Changzhou Fuku Precision Machinery Co., Ltd. , https://www.cfpmworkbench.com