3. According to different plate thickness and material, re-set the cutting speed and warm-up time in the machine, set the reasonable pressure of preheating oxygen and cutting oxygen.
4. Do not touch the flame area after ignition. Operators should take a small splash cutting method to protect the cutting nozzle.
5. Check the heating flame, and cut the oxygen jet. If it is found that the cutting nozzle is damaged, it should be promptly replaced and cleaned. The cleaning nozzle should be cleaned with special tools.
6. When a flashback occurs during the cutting process, the power supply should be cut off in a timely manner, shut down and the gas valve should be turned off. If the tempering valve piece is burned, it should be stopped and used for replacement by other manufacturers or professionals.
7. When the CNC flame operator operates the cutting machine, it is necessary to pay attention to the operation status of the equipment at all times. If abnormal conditions are found, the emergency stop switch shall be pressed to exit the work position in time and the boot is strictly prohibited from leaving the site.
8. The operator should pay attention that after cutting a workpiece, the torch should be lifted back to its original position, and then cut to the next station.
9. The operator should select the cutting speed according to the provisions of the given cutting elements. It is not allowed to increase the equipment load simply to increase the ergonomics, and the relationship between equipment life and efficiency and environmental protection should be properly handled.
Third, operate the CNC flame cutting machine after work
1. After work, the equipment should be returned to the protection position and the air valve should be closed. The residual gas in the pipe should be drained and the power turned off.
2. If the shift system is implemented, the operation status of the on-duty equipment should be recorded as a shift.
3. The site should be carefully cleaned and the work area should be kept clean and orderly.
Fourth, daily maintenance
1. Track does not allow personnel to stand, step on, rely on heavy objects, but also does not allow impact, the rail surface after each class with compressed air dusting wipe with gauze 20# oil rail surface. At any time to keep the rail surface lubrication, clean.
2. The transmission rack should be cleaned with 20# oil every day, and no spatter on the rack is allowed.
3. The operator is only allowed to disassemble the cutting nozzle, and the remaining parts cannot be disassembled. The electric junction box can only be opened when the relevant personnel are allowed to overhaul.
4. If the equipment fails, it should be promptly requested by the maintenance personnel. When the failure is large, it should be reported to the equipment department to organize the relevant personnel to review and determine the maintenance plan. It is forbidden to disassemble the machine.
Fifth, the operation of CNC flame cutting machine should pay attention to safety and security
1. Strong vibration sources should be avoided around the equipment.
2. Staff members are listed for posts, and irrelevant personnel are not allowed to board the machine, nor are they allowed to press keys without authorization so as to avoid damage to the machine or program and data loss.
3. When moving the equipment, care should be taken not to allow unhooking or pre-shooting. No part of the guide rails on the machine can hit.
4. The device power source line should be used alone, and with AC voltage regulator device.
5. Ventilation or replacement of gas and cleaning torch must be performed in accordance with the relevant dangerous gas safety operating procedures.
The above content is based on the problems encountered by the students in the actual work, for reference, if you have any questions, please communicate and correct.
The trends of the metal recycling industry
Unlike many other materials, most metal more than pays for its own recycling in the consumer and industrial waste. because the demand for metal scrap continues to rise and recycling metal saves more than 90 per cent of the energy required versus producing new metal.
The economics of metal scrap contributes to its position as one of the most recycled metals in the World.
What is the role of metal baler in metal scrap recycling?
The metal scrap can be directly pressed into bales by using the hydraulic metal baler from China factory YMSRECYCLING to make the high efficient metal recycling and increase the value of residual steel scrap.
Recycling metals also requires less energy than producing new metals. Also conserves natural resources. Recycling conserves diminishing natural resources.
How to choose a suitable metal baler?
The Y81 series Scrap Metal baler could press all ferrous metals from steel to stainless steel can be recycled as well as non-ferrous metals such as copper, brass, and aluminium, with various sizes for option, high-density compression, compact and strong. Low energy consumption but fast production rate.
Y81 series hydraulic metal baler mainly include the following models.
Y81F (side turn discharge ), Y81T (side push discharge), Y81Q (front push discharge) and Y81S (Double main press ).
We also support the design and manufacture of other model versions upon request.
Y81Q-Manual operation (Front push discharge )
Y81F-Manual operation (Side turn discharge )
Y81F-Semi-automatic operation (Side turn discharge )
Y81T-Semi-automatic operation (Side push discharge )
Y81S-Semi-automatic operation (Double main press discharge )
We provide a variety of models of the hydraulic metal baler, With new technologies to raise the quality and reduce the price, which supports 24 hours fully automatic working environment.
YMSRECYCLING offer economical and effective solutions to help you to process different metal scraps.
The Metal Baling Press can be customized and extended according to the actual needs of your on-site.
CONTACT YMSRECYCLING
Call us now on +86-15950122559
To start maximising your returns from your metal scrap recycling.
Please email sales@ymsrecycling.com or visit our website directly for further information about the products you are interested in.
Metal Baler,Aluminum Metal Recycling Baler,Automatic Aluminum Waste Metal Baler,Steel Metal Baling Press Machine
Jiangyin Yimaisheng Hydraulic Machinery Co., Ltd. , https://www.ymsrecycling.com