Model NO.: RF-ST
Main Motor Power: 5.5kw
Machine Weight: About 3 Tons
Machine Size: 6500mm X 600mm X 800mm
Warranty: 12 Months
Trademark: Suhang
Specification: CE, SGS, ISO
Origin: Wuxi, China
HS Code: 8455229090
Side by side Structure Stud Track Roll Forming Machine 

Technical Process:
Decoiler- Feeding with guide - Rollforming - Cutting - Products Collecting

Machine Components:
3 Ton passive de-coiler         1 set
Punching device                      1 set
Main roll forming machine    1 set
Cutting device                          1 set
PLC Control box                       1 unit
Hydraulic station                      1 unit
Out table                                    2 units

Technical Data:
Material of coil Material Thickness 1-2mm galvanized steel
De-coiler Weight 3 ton manual
Forming system Rolling Speed 10-12 m/min

 
embossing 1 set of rolls

 
Roller Stations About 13 stations forming, 1 set of rolls for embossing

 
Roller Material Cr40 Steel with quenching

 
Shaft Material 45# Steel Diameter 75mm shaft
 

 
Maim Motor Power 5.5 kw

 
Hydraulic cutting Power 4 kw
Cutting
system
Material Of Cutting CR12 with quench treatment

 
Hardness HRC58-62

 
Tolerance +-1.5mm

 
Cutting blade 1 set of cutting blade
Electrical control system Electric Source 380V, 50HZ,3 phase
 

 
Control System PLC Japanese Panasonic and Yaskawa Brand

 
Weight About 3 tons

 
Way Of Drive 1 inch single chain

 
Size of machine Length 6500mm* Width 600mm* Height 800m

PVC Edge Banding For Cabinet

The main function of the edge banding is to seal the cross-section of the board, so as to avoid the damage of the board and the adverse factors (mainly moisture) in the process of use and prevent the formaldehyde inside the board from volatilizing, and at the same time achieve the effect of beautiful decoration.

The product has the following main features: smooth surface, no blistering, no ribbing, moderate gloss, smooth surface and back surface, uniform thickness, uniform width, reasonable hardness, high elasticity, good quality, strong wear resistance, trimmed and sealed The color of the side and the side is close to the surface color, not whitish, good gloss, and the overall color of the finished furniture is coordinated.

Judge good or bad
1. Look at the hue and surface roughness of the edge banding strip. The color of the surface of a good edge banding strip is also very important. Whether the color is close to the customized product and is gorgeous. If the surface is very rough and there are pull marks, the quality is definitely not much better. This is the surface quality of the edge banding strip. It has nothing to do with the quality of the inner material of the edge banding, mainly the production process of the edge banding factory and the production technical skills of the employees. A good edge banding strip is: the surface must be smooth, no blistering or seldom bubbling, no drawing or few drawing, moderate gloss, not too shiny or too matte (unless there are special requirements).
2. Check the flatness of the surface and bottom of the edge banding and whether the thickness is uniform, otherwise it will cause the joint between the edge band and the board, the glue line is too eye-catching or the gap between the board and the edge band is too large, which will affect the overall beauty. Details determine success or failure, and often a small detail problem may bring an embarrassing situation where the overall effect is not good.
3. Whether the edge trimming is whitish, whether the surface of the bent edge strip is severely whitish, and whether the ground color of the trimming strip is close to the surface color of the board in question. PVC Edge Banding strips are mainly made of PVC and Calcium Carbonate plus additives. If the calcium carbonate content is too high, whitening of the edge banding and bending will occur, which proves that the quality of such products is not good.
4. Whether the strength is okay and whether there is elasticity. High strength means good wear resistance, and the corresponding quality is better. Too high strength also means increased processing difficulty. Low elasticity means low wear resistance and low aging resistance. In addition, according to actual production needs, manual trimming is generally required, and soft spots can be made appropriately, and the automatic edge banding machine can make hard points appropriately.
5. Whether the adhesive is applied evenly and whether it is easy to fall off during use.
6. Smell whether the PVC edge banding strips taste or not. Products produced with good quality raw materials generally have a small taste. If the taste is too large, it means that the quality of the raw materials used in production is relatively poor.

PVC Edge Banding For Cabinet,Pvc Edge Banding,Banding For Cabinet,T Shape Pvc Edge Banding For Kitchen Cabinet

Henan Shunbang Chemical Industry CO.,Ltd , https://www.sbcpe.com